Otter Anchor Knife Micarta Knife Lounge Exclusive The brass anchor sits so large on the green Micarta scale that you won’t have to explain to any knife nerd what you’re holding. The Otter Anchor Knife with green Micarta and an inlay of solid brass. The trick this knife brings along: it ages right alongside you. Brass tarnishes over the years, goes darker and takes on a patina. Bolsters and pins were blasted together with the anchor and the handle scales, which leaves a matt, almost velvety feel across the whole grip. So what is an anchor knife anyway? A classic slipjoint from Solingen, two-hand opening, with a sheepfoot blade whose edge runs almost dead straight while the spine curves generously above it. That shape is built for pull cuts, which is why it went to sea back in the day whenever hawsers and lines had to go. The anchor stood for hope, and sailors’ wives liked to send their men off with a knife like this. On land it butters a sandwich beautifully, by the way – just use the curved spine for that. The next picnic is coming. You get a choice of steel. C75 is a non-stainless carbon steel, a keen cutter and sharp again within minutes, though it takes on a patina and won’t thank you for a damp pocket overnight. The stain-resistant blade in 1.4034 takes that worry off your hands. Anyone taking their knife onto a boat, or not wanting to dry it off every evening, picks this one. The slipjoint spring is set good and firm, so nothing folds shut on you mid-task. Nothing locks either, and nothing opens one-handed – which is exactly why the anchor knife is § 42a compliant and may be carried in Germany. It’s made by Otter-Messer, in Solingen since 1840 and today based on Schwertstraße. The small workshop still builds traditional Solingen knives – the Mercator and this anchor knife are the classics in the range. For you that means craft that has grown over time and has run almost unchanged for generations. Who’s it for? Anyone who likes slipjoints and wants a knife that looks better with the years rather than worse. Harbour air is optional, but it does help the patina along!

Otter Anchor Knife Micarta Knife Lounge Exclusive The brass anchor sits so large on the green Micarta scale that you won’t have to explain to any knife nerd what you’re holding. The Otter Anchor Knife with green Micarta and an inlay of solid brass. The trick this knife brings along: it ages right alongside you. Brass tarnishes over the years, goes darker and takes on a patina. Bolsters and pins were blasted together with the anchor and the handle scales, which leaves a matt, almost velvety feel across the whole grip. So what is an anchor knife anyway? A classic slipjoint from Solingen, two-hand opening, with a sheepfoot blade whose edge runs almost dead straight while the spine curves generously above it. That shape is built for pull cuts, which is why it went to sea back in the day whenever hawsers and lines had to go. The anchor stood for hope, and sailors’ wives liked to send their men off with a knife like this. On land it butters a sandwich beautifully, by the way – just use the curved spine for that. The next picnic is coming. You get a choice of steel. C75 is a non-stainless carbon steel, a keen cutter and sharp again within minutes, though it takes on a patina and won’t thank you for a damp pocket overnight. The stain-resistant blade in 1.4034 takes that worry off your hands. Anyone taking their knife onto a boat, or not wanting to dry it off every evening, picks this one. The slipjoint spring is set good and firm, so nothing folds shut on you mid-task. Nothing locks either, and nothing opens one-handed – which is exactly why the anchor knife is § 42a compliant and may be carried in Germany. It’s made by Otter-Messer, in Solingen since 1840 and today based on Schwertstraße. The small workshop still builds traditional Solingen knives – the Mercator and this anchor knife are the classics in the range. For you that means craft that has grown over time and has run almost unchanged for generations. Who’s it for? Anyone who likes slipjoints and wants a knife that looks better with the years rather than worse. Harbour air is optional, but it does help the patina along!

Zero Beginner Mistakes Joseph Vero builds drones. And folding knives. And – because apparently neither of those was complicated enough – a custom electric motorcycle. With a degree in Mechanical Engineering from Florida Atlantic University and years of independent design work across multiple disciplines, one thing becomes obvious very quickly: the man does not sit still. And you can feel that energy in his products. The Nova is Joseph’s very first folder design with a dropoint blade. If you’re thinking “first attempt, let’s see how it goes” – understandable, but completely wrong. What happened between the first sketches and the finished knife was classic Vero Engineering: drawings, CAD models, 3D-printed prototypes, more drawings, sleepless nights, and eventually a knife that feels like every single detail was checked twice. Which, for a mechanical engineer, is honestly not surprising. The Nova was produced in collaboration with Bestech – the same manufacturer behind the Heidi Blacksmith Heidi #1. Meaning: Vero’s construction philosophy meets manufacturing quality that no longer needs an introduction. The titanium framelock locks up rock solid, the front flipper running on ceramic bearings deploys exactly as it should, and the CPM MagnaCut blade – 9.2 cm drop point with a high flat grind – cuts like someone set out to design the ideal everyday blade. At 21.1 cm overall length and 162 g, this is intentionally not a small knife. Instead, it gives you plenty of handle to work with and a very secure feel in hand. A nice detail: the integrated lanyard hole in the backspacer is the first one ever featured on a Vero design. Sounds minor – but it’s exactly the difference between “thought through from the start” and “added later because someone asked for it.”

Micarta handle N690 blade with a stonewashed finish includes a Kydex sheath Manufactured to strict quality standards in Maniago, Italy

Around 1880, somewhere between a fence line and a cattle drive out in the American West, cowboys needed a knife that could simply do a bit more. The stockman pattern grew out of the older cattle knife: a slipjoint that originally carried three blades on two springs. The clip blade for the rough stuff, the sheepsfoot with its straight edge and blunt tip for controlled cuts, and the spey, flat and rounded at the point, for castrating… actually, let’s not go any further into that. W.R. Case & Sons later turned the pattern into a classic of the American pocket. Jack Wolf Knives takes exactly this pattern and boils it down to the essentials. The Gateway Stockman keeps the curved handle shape and the character of the original, but comes with a single blade instead of three. That’s how Jack Wolf works across the board: classic patterns, each reduced to one blade, no matter the series. Flat-ground Sandvik 14C28N, satin finished, just under 8 cm long, a steel that shrugs off rust and takes a shaving edge again in two minutes at the kitchen table. What makes this version special: the smooth white bone scales make it a Knife Lounge exclusive. Add the Bullock shield, integral bolsters and liners in satin stainless steel, and nickel silver pins, and you get the tone of a real traditional knife without feeling dusty. It opens the classic two-handed way over the nail nick, held by the spring – walk & talk, the way a slipjoint should. Designed by Benjamin Belkin in Scottsdale, Arizona, the brand is named after his grandfather Jack Wolf, who carried slipjoints his whole life. The Gateway series is the affordable way into exactly this world, without fit and finish taking a hit. If you’re just getting into traditional pocket knives, or simply can’t resist white bone, you won’t go wrong here. Please note: This product is limited to 2 pieces per customer.

Just past midnight, the heat still hanging over the asphalt, a synth beat dripping out of an open window. Something purple flashes in the neon light. Not a drink with a little umbrella – the Divo Smallboy in Purple Nurple. Divo Knives is based in Atlanta. The Tallboy is their flagship, and the Smallboy is its little brother. Little brother doesn’t mean harmless here. The blade is CPM S90V, hollow ground, 7,6 cm long and running on ceramic bearings, so it just drops open and shut. S90V is the steel for people who want their edge to stay sharp for a long time and can’t be bothered with constant touch-ups. Kubey Knife builds the whole thing as OEM partner, and you can feel it in the tolerances. The colour runs the whole show here. The dyed CamoCarbon scales catch the light like a sunset over Ocean Drive, with collars, backspacer and clip in purple titanium – Sonny Crockett, the pastel-blazer cop from „Miami Vice“, would have carried this thing to the Ferrari without a word. The 3D-milled titanium clip rides deep, can be repositioned and fully removed if you want to rework your setup. It locks up with a nested liner lock that Divo runs as a tab lock: a small lever you work comfortably with your thumb. It opens either through the thumb hole or the thumb stud. At 17,5 cm overall and 79 g, the Smallboy sits in your pocket as a compact EDC folder without bulking up. „3 inch, very average“, as Divo describes it themselves – still enough for everything that comes up day to day, somewhere between a parcel and an apple.

Ever heard of Zoobie’s Old Town Tavern in Lansing, Michigan? Probably not — unless you happen to be sitting at that very bar right now. Doesn’t matter. What matters is that GiantMouse knows the place well, has for years: a wooden bar top, cold beer, the kind of dive where three drinks in you suddenly have friends for life. The Danish-American crew just named a knife after it. The ACE Zoobie. Let’s get this out of the way first: you’re not bringing this one to a meeting. This is a knife for the workshop, the garden, the trip where something eventually needs cutting or prying open. A big frame lock folder built for load, not for the display case. Blade in Elmax, satin finish, 89 mm long, 4 mm thick — solid edge retention, plenty tough, no drama around moisture. The frame lock opens via flipper with the clean snap you’d expect from the ACE line by now. Handles come down to preference. Full titanium, classic and pleasantly grippy at 142 g. Or black G10 scales over a titanium liner, a bit more understated and a touch lighter at 135 g in the pocket. Both versions run on the same frame, with a reversible wire clip and identical dimensions — 122 mm handle length, 211 mm open. Both are made in Maniago, Italy, the region responsible for most of Europe’s premium folders. Bottom line: not a knife that holds back. More the kind you eventually pull out and think — right, that’s why I wanted this. In titanium or black G10, whichever suits your mood.

Ever heard of Zoobie’s Old Town Tavern in Lansing, Michigan? Probably not — unless you happen to be sitting at that very bar right now. Doesn’t matter. What matters is that GiantMouse knows the place well, has for years: a wooden bar top, cold beer, the kind of dive where three drinks in you suddenly have friends for life. The Danish-American crew just named a knife after it. The ACE Zoobie. Let’s get this out of the way first: you’re not bringing this one to a meeting. This is a knife for the workshop, the garden, the trip where something eventually needs cutting or prying open. A big frame lock folder built for load, not for the display case. Blade in Elmax, satin finish, 89 mm long, 4 mm thick — solid edge retention, plenty tough, no drama around moisture. The frame lock opens via flipper with the clean snap you’d expect from the ACE line by now. Handles come down to preference. Full titanium, classic and pleasantly grippy at 142 g. Or black G10 scales over a titanium liner, a bit more understated and a touch lighter at 135 g in the pocket. Both versions run on the same frame, with a reversible wire clip and identical dimensions — 122 mm handle length, 211 mm open. Both are made in Maniago, Italy, the region responsible for most of Europe’s premium folders. Bottom line: not a knife that holds back. More the kind you eventually pull out and think — right, that’s why I wanted this. In titanium or black G10, whichever suits your mood.

Fertig montiertes Gemüsemesser mit Titan-Griffschalen im gefrästen Topo-Design. Der Name Picknicker beschreibt den Einsatzzweck ziemlich genau. Ob Brotzeit, Obst, Brötchen, Gemüse oder andere kleine Schneidaufgaben – dieses Messer ist immer dann zur Stelle, wenn ein großes Messer einfach zu viel wäre. Als Klappmesser lässt es sich kompakt und sicher verstauen und ist unterwegs jederzeit schnell einsatzbereit. Erhältlich ist der Picknicker wahlweise mit glatter Klinge oder Wellenschliff. Die glatte Schneide eignet sich hervorragend für präzise und saubere Schnitte, während der Wellenschliff besonders bei Lebensmitteln mit fester Schale oder Kruste – etwa Brot, Tomaten oder Obst – seine Stärken ausspielt. Die Basis bildet ein Victorinox Picknickmesser. Für unsere Custom-Version ersetzen wir die originalen Griffschalen durch hochwertige Titan-Griffschalen im Stonewash-Finish mit gefrästem topografischem Muster. Die von uns montierten Griffschalen werden in Deutschland gefertigt und verleihen dem Messer einen hochwertigen technischen Look mit unverwechselbarem Custom-Charakter.

in cooperation with WE Knife Toni N. Tietzel design CPM 20CV blade with hand-satin or stonewashed finish 4 carrying options, switchable with the included Hardware Kit: Two-handed – without lock Two-handed – with lock One-handed – without lock One-handed – with lock (ships in this configuration) Imagine packing your bag in the morning without having to wonder whether the knife is even allowed where you're headed. That's exactly the question Toni Tietzel — the mind behind TNT Knives — spent years chewing on. The answer is called Slip Bang, and it comes exclusively from your Knife Lounge in Hamburg. The trick: instead of picking the knife that happens to fit the law, you build the one knife to fit. With two Torx sizes you turn the Slip Bang in seconds from a two-handed slipjoint without any lock all the way up to a full one-handed locking folder. In between sit the stages with thumb stud or slider — you swap a few inlays and bits of hardware, tighten the screws, done. No special tools, no fuss. The Hardware Kit you need for that comes included with the Slip Bang. Good to know: the Slip Bang ships with the thumb studs and slider already installed, meaning it opens one-handed and locks. If you want the free, two-handed slipjoint configuration without a lock instead, just remove the thumb studs and slider. What stays constant is the part that matters most: the blade. A drop point in CPM-20CV, a steel that holds its edge for ages and doesn't fret about a bit of moisture. The grind is, as always, thin and built for cutting performance. The handle is grade-5 titanium, the stuff you'd otherwise find in aircraft parts. Locking is handled by the newly developed TNT-Lock, and the whole thing is assembled at We Knife, the parent of Civivi, who know how to put something like this together cleanly. And now the part that matters for us here in Germany. As a two-handed slipjoint without a lock, the Slip Bang doesn't fall under § 42a and is legal to carry — that's the configuration for everyday use over here. As shipped, thumb studs and slider are installed, so the knife opens one-handed and locks. Whether that unambiguously makes it an Einhandmesser under §42a isn't entirely clear — more on that below in the FAQ. On Kickstarter the Slip Bang was funded with over €54,000 — three and a half times its goal — so the scene has voted pretty clearly. The blade measures around 8.4 cm, and opened up it comes to just under 19.8 cm at just under 110 g. By default the Slip Bang comes with a stonewash finish; the satin version is limited to 150 pieces. Included in the Hardware Kit Thumbstud inlays (both sides) T6 screws for the inlays T6 screws for the thumbstuds Cover plate (for two-handed configuration) T10 slider screw T10 clip screw T10 pivot screw Pivot barrel + D-shape pivot Small V-spring for the slider Frequently asked questions about the TNT Knives Slip Bang Does it matter if you close the knife quickly, letting it slap shut? No. A stop pin prevents the blade from striking the backspring, even when closing it quickly. The stop pin is press-fitted into the blade and runs in a circular groove machined into the scales, giving a precise stop in both the open and closed positions. As far as we know, this is also a unique feature for a slipjoint, though we can't say that with absolute certainty. Is the Slip Bang an Einhandmesser under §42a as shipped? As shipped, the thumb studs and slider are installed, so the knife opens one-handed and locks. Whether that unambiguously qualifies it as an Einhandmesser under §42a WaffG isn't entirely clear, since the lock on the Slip Bang is engaged separately and, as far as we know, there's no definitive ruling on this yet. If you want to be on the safe side, carry the knife in a closed container in public, or remove the thumb studs and slider for the unlocked, two-handed configuration. Do I need extra tools to reconfigure it? You need two Torx sizes: T6 for the inlays and thumbstud screws, T10 for the slider, clip, and pivot. Both are common sizes that most multitools with a bit set cover. The Hardware Kit you need is included with the Slip Bang. How do I care for the CPM-20CV blade? CPM-20CV is corrosion-resistant, but like any steel, not fully rust-proof. After contact with moisture or acid (for example when cutting fruit), just wipe the blade down and store it dry.

in cooperation with WE Knife Toni N. Tietzel design CPM 20CV blade with hand-satin or stonewashed finish 4 carrying options, switchable with the included Hardware Kit: Two-handed – without lock Two-handed – with lock One-handed – without lock One-handed – with lock (ships in this configuration) Imagine packing your bag in the morning without having to wonder whether the knife is even allowed where you're headed. That's exactly the question Toni Tietzel — the mind behind TNT Knives — spent years chewing on. The answer is called Slip Bang, and it comes exclusively from your Knife Lounge in Hamburg. The trick: instead of picking the knife that happens to fit the law, you build the one knife to fit. With two Torx sizes you turn the Slip Bang in seconds from a two-handed slipjoint without any lock all the way up to a full one-handed locking folder. In between sit the stages with thumb stud or slider — you swap a few inlays and bits of hardware, tighten the screws, done. No special tools, no fuss. The Hardware Kit you need for that comes included with the Slip Bang. Good to know: the Slip Bang ships with the thumb studs and slider already installed, meaning it opens one-handed and locks. If you want the free, two-handed slipjoint configuration without a lock instead, just remove the thumb studs and slider. What stays constant is the part that matters most: the blade. A drop point in CPM-20CV, a steel that holds its edge for ages and doesn't fret about a bit of moisture. The grind is, as always, thin and built for cutting performance. The handle is grade-5 titanium, the stuff you'd otherwise find in aircraft parts. Locking is handled by the newly developed TNT-Lock, and the whole thing is assembled at We Knife, the parent of Civivi, who know how to put something like this together cleanly. And now the part that matters for us here in Germany. As a two-handed slipjoint without a lock, the Slip Bang doesn't fall under § 42a and is legal to carry — that's the configuration for everyday use over here. As shipped, thumb studs and slider are installed, so the knife opens one-handed and locks. Whether that unambiguously makes it an Einhandmesser under §42a isn't entirely clear — more on that below in the FAQ. On Kickstarter the Slip Bang was funded with over €54,000 — three and a half times its goal — so the scene has voted pretty clearly. The blade measures around 8.4 cm, and opened up it comes to just under 19.8 cm at just under 110 g. By default the Slip Bang comes with a stonewash finish; the satin version is limited to 150 pieces. Included in the Hardware Kit Thumbstud inlays (both sides) T6 screws for the inlays T6 screws for the thumbstuds Cover plate (for two-handed configuration) T10 slider screw T10 clip screw T10 pivot screw Pivot barrel + D-shape pivot Small V-spring for the slider Frequently asked questions about the TNT Knives Slip Bang Does it matter if you close the knife quickly, letting it slap shut? No. A stop pin prevents the blade from striking the backspring, even when closing it quickly. The stop pin is press-fitted into the blade and runs in a circular groove machined into the scales, giving a precise stop in both the open and closed positions. As far as we know, this is also a unique feature for a slipjoint, though we can't say that with absolute certainty. Is the Slip Bang an Einhandmesser under §42a as shipped? As shipped, the thumb studs and slider are installed, so the knife opens one-handed and locks. Whether that unambiguously qualifies it as an Einhandmesser under §42a WaffG isn't entirely clear, since the lock on the Slip Bang is engaged separately and, as far as we know, there's no definitive ruling on this yet. If you want to be on the safe side, carry the knife in a closed container in public, or remove the thumb studs and slider for the unlocked, two-handed configuration. Do I need extra tools to reconfigure it? You need two Torx sizes: T6 for the inlays and thumbstud screws, T10 for the slider, clip, and pivot. Both are common sizes that most multitools with a bit set cover. The Hardware Kit you need is included with the Slip Bang. How do I care for the CPM-20CV blade? CPM-20CV is corrosion-resistant, but like any steel, not fully rust-proof. After contact with moisture or acid (for example when cutting fruit), just wipe the blade down and store it dry.

Four Bombs, One Job! Probably the best-known titanium bottle opener in the EDC scene is dropping – and in four sizes at once. The Beer Bomb by NotoriousEDC is opener and little pry tool in one, machined from grade-5 titanium and made to be used rather than admired. Pick the bomb that fits you and your EDC kit: Baby Bomb – the fun-size version at 3/4 of the original. At roughly 4.8 mm and only around 17 g it lives on your keyring, in your backpack or in the glovebox. Don’t let the size fool you, it pops caps like a big one. Original – the benchmark at roughly 6.4 mm thick. The classic everything else is measured against. Big Poppa – 50 % thicker than the original, around 9.5 mm and about 60 g. Sits really solid in the hand if the standard feels too dainty for you. Atomic – twice as thick as the original, around 12.7 mm and just under 79 g. Not subtle, no question about it! If you’re after understatement, you’re in the wrong place. Why do we carry this tool? Because a comparable model was classified as a prohibited weapon by the BKA (Germany’s Federal Criminal Police Office), but we found a clean solution. Together with NotoriousEDC we developed a 3D-printed insert (with the Knife Lounge armchair, of course) that closes off the opening and puts an end to any discussion.

Dirty Deeds – the tool for the jobs your knife shouldn't have to do Notorious EDC is a US brand, and one of the few American EDC makers that actually make it to Europe. The Dirty Deeds itself is manufactured by Reate – which explains the tight tolerances and finish quality you'd normally expect from a high-end folding knife, not a pry bar. What it actually does: prying, scraping, opening packaging, popping stuck lids. All the small jobs that otherwise end up done with your knife – which then needs cleaning, and then resharpening. Grade 5 titanium, stonewashed Machined entirely from Grade 5 titanium, the same alloy used in aerospace applications. Titanium gets you close to the strength of steel at a fraction of the weight, and it doesn't corrode on its own. The stonewashed finish hides wear marks – useful for a tool that's going to live in your pocket and pick up scratches from day one. Dimensions and weight Length 89 mm Width 16 mm Thickness 5 mm Weight with clip 25 g Weight without clip 24 g Material Grade 5 Titanium Finish Stonewashed Manufacturer Reate Small enough to disappear The slim profile doesn't print in the pocket. It ships with a filler tab – a smooth titanium insert you swap in for the pocket clip if you'd rather carry it loose or in an EDC pouch. Takes a couple of minutes to switch over. Pry bars haven't quite caught on in Europe the way they have in the US, but they're starting to show up more in EDC setups here too. Once you're carrying

The Boy's Knife pattern is one of the oldest and most popular slipjoint silhouettes around — that slim, elongated handle with the gently rounded shoulders that fits the hand so naturally you wonder why anyone ever bothered doing it differently. Jack Wolf Knives took exactly that pattern as the foundation for the first FIXedc in the Gateway series. No slipjoint, no unfolding — just a simple, compact fixed blade. 15.2 cm overall length, 7.6 cm blade in Sandvik 14C28N with a flat grind and satin finish — it sits in the hand like something you've carried for years. 3 mm blade stock, 46 g without the sheath. Light enough to forget about, until you actually need it.  As always with Jack Wolf Knives, it's the handle scales that set each version apart. From understated jute micarta to bold, eye-catching options — the full range is on offer. The Gateway FIXedc ships with a Kydex sheath fitted with a reversible steel clip that adjusts to multiple carry positions, so you carry it the way it works for you, not the way the manufacturer assumed. A snake knot paracord lanyard comes pre-attached. Made in China, at a price that makes you look twice: under €80 for a fixed blade with this level of detail and these materials is, by Jack Wolf standards, no longer a surprise — but still pretty remarkable.

If you know your way around knives, you know this: a Heidi is a Heidi. Clean lines, uncompromising function, and that very specific relationship between blade and handle. That’s exactly what you get with the Heidi #3 – Knife Lounge Exclusive. Just in a production version you can actually use, without wrapping a one-off in cotton wool. The design comes directly from Heidi Blacksmith herself. This version is manufactured by Bestech, known for translating demanding designs into clean, precise production knives. The result keeps the unmistakable Heidi character while making it realistically available for everyday use. The knife features a sheepfoot blade made from 14C28N steel, finished with a subtle Knife Lounge logo. As with Heidi’s custom pieces, the blade is intentionally kept slightly shorter while the handle is extended. This balance provides excellent control and a very secure feel in hand. This is what a Heidi is meant to do: work. Precise, controlled and reliable, whether for cutting, carving or fine detail tasks. Exclusive to Knife Lounge, the Heidi #3 comes with black Micarta handle scales. The integrated groove pattern isn’t just visual – it noticeably improves grip, even when your hands aren’t perfectly dry. Functional, understated and exactly on point. Typical Heidi. A fitted Kydex sheath is included for safe, discreet carry. In your pocket, on your belt or in your pack – unobtrusive, dependable and always ready. The Heidi #3 is there when a knife needs to do more than just look good.

Picaroon Tools Swabbie You reach into your pocket, pull it out, roll the blade open with your thumb on the extended blade spine – and the Swabbie is ready to go. No button, no click, no mechanism standing between you and the blade. The Swabbie is a friction folder. The blade is held open not by a lock, but by your grip and the pressure of your thumb on the extended tang that protrudes from the back of the handle. The same lever you open it with is what keeps the blade open while you cut. Reduction as a principle – someone deliberately left things out here instead of piling them on, and you feel exactly that when you use it. The blade comes with a stonewash finish that swallows wear marks rather than putting them on display – anyone who actually uses their gear knows why that beats a mirror polish that looks like a battlefield after the first day in your pocket. The black G10 handle scales sit dry and grippy in your hand, even when things get damp outside. Harbour air included. Prefer something a bit beefier? The titanium version brings a little more weight and a distinctly more modern feel. With a 7.9 cm blade, 17.6 cm open and a 3 mm blade thickness, the Swabbie lands right in that range that simply disappears into your everyday carry. Slice an apple, open a parcel, cut a length of cord, whittle a bit by the campfire. You can carry your Swabbie either in the included simple leather pouch, or just loose in your pocket. And the best part for anyone out and about in Germany: as a friction folder with no locking blade, the Swabbie is §42a-compliant and therefore legal to carry without restriction. No hassle, no grey area – you carry a full-fledged EDC and stay on the safe side. Behind Picaroon Tools is Pavel Kukushev from Varna in Bulgaria, who grew up by the sea – hence the maritime, piratical signature of the brand. He made his name with bottle openers and tools for Kizer, Bestech and Böker – the Swabbie is his third knife design, manufactured by Bestech Knives, who have a solid reputation for executing small, idiosyncratic designs. A knife you never have to unlock, because it was never locked in the first place. That's exactly what makes it so easy to have on you every single day.

Picaroon Tools Swabbie You reach into your pocket, pull it out, roll the blade open with your thumb on the extended blade spine – and the Swabbie is ready to go. No button, no click, no mechanism standing between you and the blade. The Swabbie is a friction folder. The blade is held open not by a lock, but by your grip and the pressure of your thumb on the extended tang that protrudes from the back of the handle. The same lever you open it with is what keeps the blade open while you cut. Reduction as a principle – someone deliberately left things out here instead of piling them on, and you feel exactly that when you use it. The blade comes with a stonewash finish that swallows wear marks rather than putting them on display – anyone who actually uses their gear knows why that beats a mirror polish that looks like a battlefield after the first day in your pocket. The black G10 handle scales sit dry and grippy in your hand, even when things get damp outside. Harbour air included. Prefer something a bit beefier? The titanium version brings a little more weight and a distinctly more modern feel. With a 7.9 cm blade, 17.6 cm open and a 3 mm blade thickness, the Swabbie lands right in that range that simply disappears into your everyday carry. Slice an apple, open a parcel, cut a length of cord, whittle a bit by the campfire. You can carry your Swabbie either in the included simple leather pouch, or just loose in your pocket. And the best part for anyone out and about in Germany: as a friction folder with no locking blade, the Swabbie is §42a-compliant and therefore legal to carry without restriction. No hassle, no grey area – you carry a full-fledged EDC and stay on the safe side. Behind Picaroon Tools is Pavel Kukushev from Varna in Bulgaria, who grew up by the sea – hence the maritime, piratical signature of the brand. He made his name with bottle openers and tools for Kizer, Bestech and Böker – the Swabbie is his third knife design, manufactured by Bestech Knives, who have a solid reputation for executing small, idiosyncratic designs. A knife you never have to unlock, because it was never locked in the first place. That's exactly what makes it so easy to have on you every single day.

The Compact Fixed Beast 7 mm blade stock. Seven. That’s not a typo. For a knife of this size, that’s roughly the equivalent of putting a ship engine into a compact car — slightly absurd, but also kind of amazing. Imagine Jesper Voxnaes sitting at his workbench late at night, thinking: What if a fixed blade could be as compact and easy to carry as a good folder — but strong enough to pry open a submarine hatch if necessary? The result is the GiantMouse GMF5: a pocket-sized fixed blade built with serious overkill in mind. The blade is made from N690 steel, an Austrian steel well known for its excellent corrosion resistance, solid edge retention, and easy maintenance. In other words: a proven all-rounder that works just as well in everyday carry as it does outdoors. The full flat grind tapers down cleanly for efficient cutting performance, while depending on the version, the knife comes with either a satin or PVD finish. To keep the GMF5 from becoming completely excessive, GiantMouse intentionally skipped traditional handle scales. Instead, you get an old-school full-steel construction with signature speed holes that reduce weight without sacrificing rigidity. The handle end even hints at a small prybar / impact tool function — just in case a coconut suddenly needs to lose an argument. Despite its heavy-duty construction, the knife remains genuinely EDC-friendly. The included Kydex sheath allows for flexible carry options — pocket, belt, backpack straps, whatever fits your setup best. And thanks to the blade length staying under 12 cm, the GMF5 remains perfectly legal to carry as an EDC fixed blade.

The Compact Fixed Beast 7 mm blade stock. Seven. That’s not a typo. For a knife of this size, that’s roughly the equivalent of putting a ship engine into a compact car — slightly absurd, but also kind of amazing. Imagine Jesper Voxnaes sitting at his workbench late at night, thinking: What if a fixed blade could be as compact and easy to carry as a good folder — but strong enough to pry open a submarine hatch if necessary? The result is the GiantMouse GMF5: a pocket-sized fixed blade built with serious overkill in mind. The blade is made from N690 steel, an Austrian steel well known for its excellent corrosion resistance, solid edge retention, and easy maintenance. In other words: a proven all-rounder that works just as well in everyday carry as it does outdoors. The full flat grind tapers down cleanly for efficient cutting performance, while depending on the version, the knife comes with either a satin or PVD finish. To keep the GMF5 from becoming completely excessive, GiantMouse intentionally skipped traditional handle scales. Instead, you get an old-school full-steel construction with signature speed holes that reduce weight without sacrificing rigidity. The handle end even hints at a small prybar / impact tool function — just in case a coconut suddenly needs to lose an argument. Despite its heavy-duty construction, the knife remains genuinely EDC-friendly. The included Kydex sheath allows for flexible carry options — pocket, belt, backpack straps, whatever fits your setup best. And thanks to the blade length staying under 12 cm, the GMF5 remains perfectly legal to carry as an EDC fixed blade.

Compact fixed blade for pocket carry Handle material: Black Canvas Micarta or Green Linen Micarta Mostly handcrafted by founder Michael Jarvis Exclusive to Knife Lounge Includes Boltaron sheath with clip

Compact fixed blade for pocket carry Rietveld Damascus steel (non-stainless) Handle material: Black Canvas Micarta or Green Linen Micarta Mostly handcrafted by founder Michael Jarvis exclusively for Knife Lounge Includes Boltaron sheath with clip

Small. Lightweight. Always with you. The Auxiliary Mfg Pocket Lint is the fixed blade for people who normally don’t carry a fixed blade — and then suddenly never leave home without it again. With a 1.73" spear point blade made from AEB-L steel, this knife delivers far more than its size would suggest. AEB-L is known for its fine grain structure, easy maintenance, and razor-sharp edge performance that simply makes everyday cutting enjoyable. The green Micarta handle gives the knife its distinctive character. Micarta feels great in hand, ages beautifully over time, and develops a unique patina that makes every knife its own piece. Exactly what you want from a handmade knife. The Pocket Lint comes with a Kydex sheath and key ring — practical, compact, and always ready when you need it. Small enough to forget it’s there, good enough to miss when it’s not. Blade length: approx. 1.73" / 4.4 cm Blade steel: AEB-L Blade shape: Spear Point Handle material: Green Micarta Sheath: Kydex with key ring Handmade by Michael Jarvis

The Doctor's Knife. Reimagined. The Feelbetter Jack by Jack Wolf Knives is a modern tribute to the classic doctor’s knife – a nearly forgotten blade pattern that Jack Wolf has brought back to life with precision engineering and contemporary design. The result: an exceptional EDC knife that combines tradition, craftsmanship, and premium materials in a truly remarkable way. Blade The Wharncliffe blade crafted from Crucible S90V steel delivers outstanding edge retention and ease of sharpening. The hollow grind provides a sharp, precise cutting edge, while the belt satin finish impresses both visually and functionally. With a blade length of 3.38″ and a cutting edge of 2.98″, the Feelbetter Jack is perfectly suited for everyday carry and use. Mechanism & Construction The Feelbetter Jack opens smoothly via a front flipper tab or the double-sided long pull, locking securely into a frame lock (bolster lock). Ceramic bearings ensure a buttery-smooth, effortless open and close. Integral bolsters and liners in bronze anodized titanium lend the knife a refined look and excellent structural integrity. Handle & Fit and Finish The handle is available in several stunning configurations – including Carbon Fiber, Kirinite, Purple Abalone and Dark Blasted Titanium Starburst. Every variant combines a striking appearance with a comfortable, confident grip. Depending on the handle material, the knife weighs between approximately 2.3 and 2.7 oz – light enough for the pocket, refined enough for the display shelf.

The Doctor's Knife. Reimagined. The Feelbetter Jack by Jack Wolf Knives is a modern tribute to the classic doctor’s knife – a nearly forgotten blade pattern that Jack Wolf has brought back to life with precision engineering and contemporary design. The result: an exceptional EDC knife that combines tradition, craftsmanship, and premium materials in a truly remarkable way. Blade The Wharncliffe blade crafted from Crucible S90V steel delivers outstanding edge retention and ease of sharpening. The hollow grind provides a sharp, precise cutting edge, while the belt satin finish impresses both visually and functionally. With a blade length of 3.38″ and a cutting edge of 2.98″, the Feelbetter Jack is perfectly suited for everyday carry and use. Mechanism & Construction The Feelbetter Jack opens smoothly via a front flipper tab or the double-sided long pull, locking securely into a frame lock (bolster lock). Ceramic bearings ensure a buttery-smooth, effortless open and close. Integral bolsters and liners in bronze anodized titanium lend the knife a refined look and excellent structural integrity. Handle & Fit and Finish The handle is available in several stunning configurations – including Carbon Fiber, Kirinite, Purple Abalone and Dark Blasted Titanium Starburst. Every variant combines a striking appearance with a comfortable, confident grip. Depending on the handle material, the knife weighs between approximately 2.3 and 2.7 oz – light enough for the pocket, refined enough for the display shelf.